Panasonic Industry ／ 制御機器
MENU
Panasonic Industry ／ 制御機器

HL-AC1P｜超小型雷射線性感測器 HL-T1

下載

※ 實際商品可能與照片不同。

適合不含有規定:EU RoHS指令 2011/65/EU的6物質、以及EU RoHS指令2015/863/EU的4物質

品名

HL-AC1P

型號

HL-AC1P

產品

Ultra-compact Laser Collimated Beam Sensor

詳細

Controller (PNP output)

商品名稱

 超小型雷射線性感測器 HL-T1

聯繫我們

※為了商品改進，規格和外觀可能會在不事先通知的情況下變更，敬請諒解。

詳細規格

為了商品改進，規格和外觀可能會在不事先通知的情況下變更，敬請諒解。
項目內容
品名HL-AC1P
型號HL-AC1P
產品名Ultra-compact Laser Collimated Beam Sensor
顯示價格Please contact our office
TypePNP output
Applicable regulationsEMC Directive, RoHS Directive
Applicable sensor headHL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F
電源電壓12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
消耗電流190 mA or less (when connected to the sensor head)
Measuring cycle150 micro s
Linear outputCurrent / voltage output switchable (Note)
-During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm
-During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm
(In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.)
(Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller.
Linear output : Temperature characteristicsplus or minus 0.2 % F.S./℃
(Note) These are the temperature characteristics of the linear output when the sensor head is connected.
Settable average sampling rate1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096
(Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1).
Judgment outputs (HIGH, PASS, LOW)PNP open-collector transistor
-Maximum source current: 50 mA
-Applied voltage: 30 V DC or less (between judgment output and +V)
-Residual voltage: 2 V or less (at 50 mA source current)
Judgment outputs (HIGH, PASS, LOW) : Utilization categoryDC-12 or DC-13
Judgment outputs (HIGH, PASS, LOW) : Number of outputsHIGH / PASS / LOW 3 values output
Judgment outputs (HIGH, PASS, LOW) : Output operationHIGH: ON when measured value > HIGH threshold value
PASS: ON when HIGH threshold value >= measured value >= LOW threshold value
LOW: ON when LOW threshold value > measured value
Judgment outputs (HIGH, PASS, LOW) : Short-circuit protectionIncorporated
Laser OFF input+V connection: Laser emission halt
Open: Laser emission
-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
Zero reset input+V connection: Zero reset operates
Open: Zero reset ineffective
-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
Timing input+V connection: Effective
Open: Ineffective
-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
Reset input+V connection: Effective
Open: Ineffective
-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less)
Indicators : Laser emitting (LD ON)Green LED (lights up during laser emission)
Indicators : Judgment outputsHIGH: Orange LED (lights up when measured value > HIGH threshold value)
PASS: Green LED (lights up when HIGH threshold value >= measured value >= LOW threshold value)
LOW: Yellow LED (lights up when LOW threshold value > measured value)
Indicators : Enable (ENABLE)Green LED (lights up during normal operation)
Indicators : Zero reset (ZERO)Green LED (lights up when the zero reset function is enabled)
Main digital display5 digit red LED display
[RUN mode: Either the measured value (mm) or the hold value will be displayed. Reverse mode: The display orientation will be reversed.]
Sub-digital display5 digit yellow LED display
[RUN mode: Either the resolution or laser beam reception amount will be displayed. THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.]
Main functions・Measured value display
・Setting value, light amount value resolution display
・Standard received light setting
・Automatic scaling
・Scaling
・Display reverse
・ECO display
・Display digits limitation
・Sample hold
・Peak hold
・Bottom hold
・Peak to peak hold
・Self peak hold
・Self bottom hold
・Zero reset
・Initial reset
・ON-delay timer
・OFF-delay timer
・One-shot timer
・Differentiation
・Sensitivity selection
・Threshold value direct setting
・Positioning teaching
・2-point teaching
・Automatic teaching
・Hysteresis width variability
・Monitor focus
・Non-measuring time setting
・(A – B) calculation(Note：The calculation unit is necessary.)
・(A + B) calculation(Note：The calculation unit is necessary.)
・Mutual interference prevention (Note：The calculation unit is necessary.)
・Laser deterioration detection
・Key lock
・Zero reset memory
汚損度3 (industrial environment)
Environmental resistance : Ambient temperature0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), Storage: -25 to +65 ℃ -13 to +149 ℉
Environmental resistance : Ambient humidity35 to 85 % RH, Storage: 35 to 85 % RH
Voltage withstandability1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance20 MOhm , or more, with 500 V DC megger between all supply terminals connected together and enclosure
Environmental resistance : Vibration resistance10 to 150 Hz frequency, 0.7 mm 0.028 in double amplitude in X, Y and Z directions for 80 min.
Environmental resistance : Shock resistance300 m/s2 acceleration (30 G approx.) in X, Y and Z directions three times each
材質Enclosure: Polybutylene terephthalate
Transparent cover: Polycarbonate
I/O cable0.09 mm2 10-core composite cable, 2 m 6.562 ft long
I/O cable extensionExtension up to total 10 m 32.808 ft is possible, with 0.09 mm2 or more, cable.
(Note) If the extension cable is longer than 10 m 32.808 ft, then it will not qualify for CE marking.
重量Net weight: 140 g approx.

MENU

最近搜尋過的產品

最近搜尋過的產品型號