{lead}
{name}
  • {name}
  • 日本語
  • English (Global)
  • English (Asia Pacific)
  • 简体中文
  • 繁體中文
  • 한국어
▼
Panasonic Industry / Automation Controls
MENU
Panasonic Industry / Automation Controls

ER-X001｜Pulse AC Method Area Ionizer ER-X

Download

*Photo may vary from actual product.

This product has been confirmed that it does not contain the 6 substances specified in EU RoHS Directive 2011/65/EU and the 4 substances specified in 2015/863/EU.

Product Number

ER-X001

Part Number

ER-X001

Product

Pulse AC Method Area Ionizer

Details

Head

Product Name

 Pulse AC Method Area Ionizer ER-X

Contact Us

*Specifications and design of the products are subject to change without notice for the product improvement.

Spec Detail

Specifications and design of the products are subject to change without notice for the product improvement.
ItemSpecifications
Part NumberER-X001
Product NumberER-X001
Products NamePulse AC Method Area Ionizer
Product detailsHead
The price of the productPlease contact our office
Applicable regulations and certificationsCE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations), TÜV SÜD certification (USA, Canada)
Effective charge removal width50 mm 1.969 in approx.
Charge removal time0.3 sec. or less (Note 1), 0.5 sec. or less (Note 2)
(Note 1： Typical value in condition of discharge distance 50 mm 1.969 in, center of the product, discharge wavelength 50 Hz and air supply 60 ℓ / min. (0.3 MPa)) .
(Note 2： Typical value in condition of discharge distance 50 mm 1.969 in, center of the product, discharge wavelength 50 Hz and no air supply.)
Ion balance±30 V or less
(Note 1：Typical value in condition of discharge distance 100 mm 3.937 in, center of the product, discharge frequency 30 Hz and no air supply.)
(Note 2： Ion balance refers to the average value of plus and minus. The specification value is the typical one in condition used when ambient temperature change is less than ±10 ℃, ion balance is set after 30 minutes from the discharge start, the ion balance control function is set ON.)
Discharge methodPulse AC method
(Note：The discharge frequencies of 50 Hz, 20 Hz are accepted.)
Discharge frequency50 Hz / 20 Hz
Discharge output voltage±7,000 V approx.
Ozone generation0.01 ppm or less
(Note：Typical value in condition of discharge distance 50 mm 1.969 in, center of the product, discharge wavelength 50 Hz and no air supply.)
Maximum air pressure0.5 MPa
Applicable fluidAir (dried clean air)
(Note：The dried clean air is the air dried (dew point: equivalent of -20 ℃ -4 ℉) and filtered (mesh-size: equivalent of 0.01 μm) .)
Operating altitude2,000 m 6561.68 ft or less
(Note：Do not use or store in an environment that has been pressurized to an air pressure higher than the atmospheric pressure at 0 m.)
Ambient temperature0 to +40 ℃ +32 to +104 ℉ (No dew condensation), Storage: -10 to +65℃ +14 to +149℉
Ambient humidity35 to 65 % RH, Storage: 35 to 85 % RH
Vibration resistance10 to 55 Hz frequency, 0.75 mm 0.030 in (Max. acceleration 50 m/s2) double amplitude in X, Y and Z directions for two hours each
Shock resistance100 m/s2 acceleration (10 G approx.), in X, Y and Z directions three times each
Enclosure earthingFloating
MaterialMain unit enclosure: Stainless steal (SUS)
Head mounting bracket: Stainless steal (SUS)
Discharge needle: PFA, Tungsten
Length of high-voltage cable1.2 m 3.937 ft
WeightNet weight : 370 g approx.
AccessoriesHead mounting bracket (installed at the time of factory shipment)

MENU

Recently checked products

Recently checked product numbers