{lead}
{name}
  • {name}
  • 日本語
  • English (Global)
  • English (Asia Pacific)
  • 简体中文
  • 繁體中文
  • 한국어
▼
Panasonic Industry / Automation Controls
MENU
Panasonic Industry / Automation Controls

EC-G02｜Pulse Air-gun Ionizer EC-G

Download

*Photo may vary from actual product.

This product has been confirmed that it does not contain the 6 substances specified in EU RoHS Directive 2011/65/EU and the 4 substances specified in 2015/863/EU.

Product Number

EC-G02

Part Number

EC-G02

Product

Pulse Air-gun Ionizer

Details

Gun type

Product Name

 Pulse Air-gun Ionizer EC-G

Contact Us

*Specifications and design of the products are subject to change without notice for the product improvement.

Spec Detail

Specifications and design of the products are subject to change without notice for the product improvement.
ItemSpecifications
Part NumberEC-G02
Product NumberEC-G02
Products NamePulse Air-gun Ionizer
Product detailsGun type
Applicable regulationsCE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations)
Charge removal time0.5 sec. or less approx. (±1,000 V → ±100 V)
Note : Typical value for continuous pulse air mode at 100 mm 3.937 in from the end of discharge nozzle at an applied air pressure of 0.50 MPa.
Ion balance±10 V or less
Note : Typical value for continuous pulse air mode at 100 mm 3.937 in from the end of discharge nozzle at an applied air pressure of 0.50 MPa.
Applicable fluidAir (dried clean air)
(Note):Dried clean air is the air passing through air dryer (dew point -20 ℃ -4 ℉ approx.) and air filter (mesh size 0.01 μm 0.0004 mil approx.)
Supplied air flow300 ℓ/min. (ANR) or less
Air pressure range0.05 to 0.50 MPa
Supply voltageAccessory AC adapter
• INPUT: 100-240 V AC ±10 % 50/60 Hz
• OUTPUT: 24 V DC
Operating voltage of ionizer body: 24V DC
Power consumption30 VA or less
Discharge methodHigh-frequency AC method
Discharge output voltageApprox. 2,000 V
Ozone generation0.02 ppm or less
Note : Typical value for continuous pulse air mode at 300 mm 11.881 in from the end of discharge nozzle at an applied air pressure of 0.25 MPa.
Pulse air modePulse 1 (long) / Pulse 2 (short) / CONT (continuous) selectable by switch
LED illumination modeON (always ON) / SYNC (synchronized with trigger) / OFF (always OFF)
External inputIonized air emission operation ON / OFF using OR control with trigger switch
Ionized air emission operation ON: Short-circuited to COM (-)
Ionized air emission operation OFF: Open
Operating altitude2,000 m or less
Note : Do not use or store the device in an environment where the air pressure is higher than the atmospheric pressure at an altitude of 0 m.
Ambient temperature0 to +50 ℃ +32 to +122 ℉ (No dew condensation allowed), AC adapter: 0 to +40 ℃ +32 to +104 ℉
Ambient humidity35 to 65 % RH (No dew condensation allowed)
MaterialEnclosure: ABS, Nozzle: Stainless steel, Discharge needle: Tungsten, Nozzle guard: NBR
Weight270 g approx. (main unit only)
AccessoriesAC adapter (manufactured by ENG ELECTRIC, model: 6A-181-WP24): 1 pc.
Exclusive intermediate cable (oil-resistant, heat-resistant, bending-resistant type) length 2 m 6.562 ft: 1 pc.
Straight joints
• Tube outer diameter ø8-ø8 mm ø0.315-ø0.315 in compatible type: 1 pc.(Note: Typical value for continuous pulse air mode at 300 mm 11.881 in from the end of discharge nozzle at an applied air pressure of 0.25 MPa.)
• Tube outer diameter ø8-ø6 mm ø0.315-ø0.236 in compatible type: 1 pc.
• Connector connection terminal (Manufactured by Molex): 3 pcs.
RemarkWhere measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉.

MENU

Recently checked products

Recently checked product numbers