Panasonic Industry / Automation Controls
MENU
Panasonic Industry / Automation Controls

LS-501P-C2｜Amplifier-separated Type Digital Laser Sensor LS-500

Download

*Photo may vary from actual product.

This product has been confirmed that it does not contain the 6 substances specified in EU RoHS Directive 2011/65/EU and the 4 substances specified in 2015/863/EU.

Product Number

LS-501P-C2

Part Number

LS-501P-C2

Product

Amplifier-separated Type Digital Laser Sensor

Details

Amplifiers(Cable type)

Product Name

 Amplifier-separated Type Digital Laser Sensor LS-500

Contact Us

*Specifications and design of the products are subject to change without notice for the product improvement.

Spec Detail

Specifications and design of the products are subject to change without notice for the product improvement.
ItemSpecifications
Part NumberLS-501P-C2
Product NumberLS-501P-C2
Products NameAmplifier-separated Type Digital Laser Sensor
Product detailsAmplifiers(Cable type)
The price of the productPlease contact our office
Applicable regulationsEMC Directive, RoHS Directive
Operation indicatorOrange LED (lights up when sensing output 1 or sensing output 2 is ON)
ProtectionIP40(IEC)
Ambient temperature-10 to +55degrees + 14 to 131 degrees Fahrenheit (If 4 to 7 units are mounted close together, -10 to +50 degrees +14 to +122 degrees Fahrenheit ; if 8 to 12 units are mounted close together, -10 to +45 degrees +14 to +113 degrees Fahrenheit )(No dew condensation or icing allowed), Storage: -20 to +70 degrees -4 to +158 degrees Fahrenheit
Ambient humidity35 to 85 % RH, Storage: 35 to 85 % RH
Voltage withstandability1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration resistance10 to 150 Hz frequency, 1.5 mm 0.059 in double amplitude or maximum acceleration 98 m/s2 in X, Y and Z directions for two hours each
Shock resistance98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each
MaterialEnclosure: Polycarbonate
Cover: Polycarbonate
Switch: Polyacetal
Cable0.2mm2 6-core cabtyre cable, 2 m 6.562 ft long
(Note：Cable cannot be extended.)
WeightNet weight: 75 g approx.
Gross weight: 110 g approx.
AccessoryFX-MB1 (Amplifier protective seal): 1 set
Supply voltage12 to 24 V DC +10-15% Ripple P-P 10 % or less
Power consumptionNormal operation: 1,200 mW or less (Current consumption 50 mA or less at 24 V supply voltage,excluding monitor current output)
ECO mode: 980 mW or less (Current consumption 40 mA or less at 24 V supply voltage,excluding monitor current output)
Sensing outputs (Sensing output 1, 2)PNP open-collector transistor
・Maximum source current: 50 mA (Note：25 mA if 5 or more amplifier are connected in cascade (excluding cable extension).)
・Applied voltage: 30 V DC or less (between output and +V)
・Residual voltage: 2 V or less (at max. source current)
(Note：Select either sensing output 2 or external input as the connector type.)
Sensing outputs (Sensing output 1, 2):Output operationSelectable either Light-ON or Dark-ON
Sensing outputs (Sensing output 1, 2):Short-circuit protectionIncorporated
Sensing output setting:Sensing output 1Normal mode, differential mode, hysteresis mode, window comparator mode, selectable
Sensing output setting:Sensing output 2Normal mode, differential mode, hysteresis mode, self-diagnostic output mode, answer-back output mode, selectable
(Note：Select either sensing output 2 or external input.)
Response timeH-SP: 60 micro s or less, FAST: 150 micro s or less, STD: 250 micro s or less, LONG: 500 micro s or less, U-LG: 5 ms or less, HYPR: 24 ms or less selectable
Monitor current outputOutput current: Approx. 4 to 20 mA (H-SP, FAST, STD: at 0 to 4,000 indication)
Response time: 2 ms or less
Zero point: 4 mA plus or minus 1 % F.S.
Span: 16 mA plus or minus 5 % F.S.
Linearity: plus or minus 3 % F.S.
Load resistance: 0 to 250 Ohm
External inputPNP non-contact input
- Signal condition High: +4 Vto+V DC(sink current 3.0 mA or less), Low: 0 to +0.6 V DC or open
- Input impedance: 10 kOhm approx.(Note：Select either sensing output 2 or external input.)
External input functionLaser emission halt / teaching (full-auto teaching, limit teaching, 2 point teaching) / logic operation setting / copy lock /display adjustment / data bank load / data bank save, selectable
Laser emission indicatorGreen LED (lights up during laser emission)
Output select indicatorYellow LED (lights up when output is selected)
Digital display8-digit 7-segment digital display (4-digit green LED + 4-digit red LED), MODE indicator (Yellow LED): L/D, CUST, PRO
Incident light indication rangeH-SP/FAST/STD: 0 to 4,000
LONG/U-LG/HYPR: 0 to 9,999
Sensitivity setting2-level teaching / limit teaching / full auto teaching / manual adjustment
Logical operationBetween sensing output 1 and calculation target: Disabled / and / or / xor, selectable
Calculation target: Sensing output 2 / adjacent upstream amplifier (sensing output 1) / external input, selectable
Timer function
OFF-delay timer, ON-delay timer, ONE-SHOT timer, ON / OFF-delay timer, ON-delay / ONE-SHOT timer,
switchable either effective of ineffective, with variable timer period

OFF-delay timer, ON-delay timer, ONE-SHOT timer,
switchable either effective of ineffective, with variable timer period
Timer function:TimeTimer range '' ms'': 0.5 ms approx., 1 to 9,999 ms approx., in approx. 1 ms intervals
Timer range '' sec'': 0.5 sec. approx., 1 to 32 sec. approx., in approx. 1 sec. intervals
Timer range '' 1/10 ms'': 0.05 ms approx., 0.1 to 999.9 ms approx., in approx. 0.1 ms intervals, Set separately for each output.
Automatic interference prevention functionIncorporated
(Note：Number of units that can be mounted close together: 0 for H-SP; 2 for FAST; 4 for STD, LONG, U-LG, or HYPR)
Cable extensionExtension up to total 100 m 328.084 ft is possible with 0.3mm2, or more, cable.

MENU

Recently checked products

Recently checked product numbers