------------------------------ Tab1 showing ------------------------------
Basic Information
Eight types of mounting stands enable installation of sensors,
fibers, and reflectors at any desired position
Features
Easy adjustment of sensing position
Even after mounting a sensor, you can adjust the sensor easily.
Note: The elevation angle is ±20° for MS-AJ□-F (assembly for fiber).
Mountable on vertical or horizontal plane
MS-AJ1(-□)
Securely fixed with two M6 screws
Cable can be neatly threaded into pipe
Note: Do not thread the fiber cable
into the pipe in case of MS-AJ-F
(assembly for fiber).
Eight models
MS-AJ□ (Basic assembly)
It is used to mount CX-400, LS, EX-40 and EZ-10 series sensors, and the RF-210 reflector.
MS-AJ□-A (Lateral arm assembly)
A lateral arm is added to the MS-AJ□ basic assembly. Sensing is possible from above an assembly line.
MS-AJ□-M (Assembly for reflector)
The MS-AJ□ basic assembly is modified to mount a reflector. It can be used for RF-220 and RF-230 reflectors.
MS-AJ□-F (Assembly for fiber)
The sensor mounting bracket of MS-AJ□-A is replaced with a fiber mounting bracket. It can be used with FD-L51, FD-L52, FD-L53, FD-L54 and M3, M4 or M6 threaded head fibers.
------------------------------ Tab2 showing ------------------------------
Order guide
| Type | Appearance | Model No. | Applicable sensor, reflector and fiber | |
|---|---|---|---|---|
| Basic assembly | Horizontal mounting type |
| MS-AJ1 | CX-400 series CX-L400 series LS series EQ-20 series (Note) EX-40 series EZ-10 series RF-210 (Reflector) |
| Vertical mounting type | MS-AJ2 | |||
| Lateral arm assembly | Horizontal mounting type |
| MS-AJ1-A | |
| Vertical mounting type | MS-AJ2-A | |||
| Assembly for reflector | Horizontal mounting type |
| MS-AJ1-M | RF-220 (Reflector) RF-230 (Reflector) |
| Vertical mounting type | MS-AJ2-M | |||
| Assembly for fiber | Horizontal mounting type |
| MS-AJ1-F | FD-L51 (Fiber) FD-L52 (Fiber) FD-L53 (Fiber) FD-L54 (Fiber) M3, M4 and M6 threaded head fibers |
| Vertical mounting type | MS-AJ2-F | |||
Note:
The EQ-20 series was discontinued in December 2005.
Individual components are also available as follows
| Designation | Appearance | Model No. |
|---|---|---|
| Sensor mounting unit |
| MS-AJS |
| Reflector mounting unit |
| MS-AJR |
| Reflector mounting bracket |
| MS-AJ-R1 |
| Fiber mounting unit |
| MS-AJD |
| Fiber mounting bracket |
| MS-FD-1 |
| Arm joint unit |
| MS-AJL |
| Base unit (Horizontal mounting type) |
| MS-AJ1B |
| Base unit (Vertical mounting type) |
| MS-AJ2B |
| Cable guide |
| MS-AJG |
| Arm (Pipe) |
| MS-AJP |
Discontinued products
* Substitute products will not guarantee the specifications of discontinued products.
Please check the specification details from catalog before use.
| Discontinued product | Recommended substitute | ||||
|---|---|---|---|---|---|
| Product number/Part number | Last time buy | Product number/Part number | Product name | Remark | |
| Product number: MS-AJ Part number: MS-AJ | August 31, 2003 To be discontinued |
| Product number: - Part number: MS-AJ1,MS-AJ2 | Universal Sensor Mounting Stand MS-AJ | Suggested alternative products may be different under the conditions of use. |
| Product number: MS-AJ-A Part number: MS-AJ-A | August 31, 2003 To be discontinued |
| Product number: - Part number: MS-AJ1-A,MS-AJ2-A | Universal Sensor Mounting Stand MS-AJ | Suggested alternative products may be different under the conditions of use. |
| Product number: MS-AJ-F Part number: MS-AJ-F | August 31, 2003 To be discontinued |
| Product number: - Part number: MS-AJ1-F,MS-AJ2-F | Universal Sensor Mounting Stand MS-AJ | Suggested alternative products may be different under the conditions of use. |
| Product number: MS-AJ-M Part number: MS-AJ-M | August 31, 2003 To be discontinued |
| Product number: - Part number: MS-AJ1-M,MS-AJ2-M | Universal Sensor Mounting Stand MS-AJ | Suggested alternative products may be different under the conditions of use. |
| Product number: MS-AJB Part number: MS-AJB | August 31, 2003 To be discontinued |
| Product number: - Part number: MS-AJ1B,MS-AJ2B | Universal Sensor Mounting Stand MS-AJ | Suggested alternative products may be different under the conditions of use. |
------------------------------ Tab3 showing ------------------------------
Dimensions
- Unit: mm in
MS-AJ1
Basic assembly
Two M3 (length 14 mm0.551 in) screws with washers, two M3 (length 16 mm0.630 in) screws with washers, two M3 (length 18 mm0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attached.Note:The dimensions in the brackets indicate the adjustable range of the movable part.
MS-AJ2
Basic assembly
Two M3 (length 14 mm0.551 in) screws with washers, two M3 (length 16 mm0.630 in) screws with washers, two M3 (length 18 mm0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attachedNote:The dimensions in the brackets indicate the adjustable range of the movable part.
MS-AJ1 MS-AJ2
Basic assembly
Assembly dimensions with CX-400/440 series,LS-400 series, EZ-10 series
(Mounting part only)
Assembly dimensions with EX-40 series
(Mounting part only)
Assembly dimensions with RF-210 (Reflector)
(Mounting part only)
MS-AJ1-M
Assembly for reflector
Two M3 (length 8 mm0.315 in) screws with washers and two M4 (length 8 mm0.315 in) screws with washers are attached.Note:The dimensions in the brackets indicate the adjustable range of the movable part.
MS-AJ2-M
Assembly for reflector
Two M3 (length 8 mm0.315 in) screws with washers and two M4 (length 8 mm0.315 in) screws with washers are attached.Note:The dimensions in the brackets indicate the adjustable range of the movable part.
MS-AJ1-M MS-AJ2-M
Assembly for reflector
Assembly dimensions with RF-220 (Reflector)
(Mounting part only)
Assembly dimensions with RF-230 (Reflector)
(Mounting part only)
MS-AJ1-A
Lateral arm assembly
Two M3 (length 14 mm0.551 in) screws with washers, two M3 (length 16 mm0.630 in) screws with washers, two M3 (length 18 mm0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attached.Notes:1) The dimensions in the brackets indicate the adjustable range of the movable part.2) Refer to MS-AJ1/MS-AJ2 (basic assembly) for the assembly diagram with the sensor mounting bracket, sensor or reflector.
MS-AJ2-A
Lateral arm assembly
Two M3 (length 14 mm0.551 in) screws with washers, two M3 (length 16 mm0.630 in) screws with washers, two M3 (length 18 mm0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attached.Notes:1) The dimensions in the brackets indicate the adjustable range of the movable part.2) Refer to MS-AJ1/MS-AJ2 (basic assembly) for the assembly diagram with the sensor mounting bracket, sensor or reflector.
MS-AJ1-F
Assembly for fiber
Note:1) The dimensions in the brackets indicate the adjustable range of the movable part.
MS-AJ2-F
Assembly for fiber
Notes:1) The dimensions in the brackets indicate the adjustable range of the movable part.
MS-AJ1-F MS-AJ2-F
Assembly for fiber
Fiber mounting bracket / MS-FD-1
Material:Stainless steel (SUS304)
Assembly dimensions with FD-L51
(Mounting part only)
Assembly dimensions with FD-FM2
(Mounting part only)
Note:The above diagram is in case of M6 threaded head fiber.
------------------------------ Tab4 showing ------------------------------
Cautions For Use
Mounting
- To mount the universal sensor mounting stand on your equipment, use M6 screws. The tightening torque should be 2.0 Nm or less.
Adjustment
- Arm, attachment, base and arm joint can be adjusted as shown by the arrows in the right figure by loosening the M4 hexagonsocket-head bolts.
- After the adjustment, the tightening torque of the M4 hexagon-socket-head bolts should be 1.2 Nm or less.
Threading cable into pipe
- When the sensor is mounted on MS-AJ□ (basic assembly) or on MS-AJ□-A (lateral arm assembly), the sensor cable can be threaded through the pipe. However, do not thread the fiber cable through the pipe when a fiber head is mounted on MS-AJ□-F (assembly for fiber).
Others
- Do not apply excessive force on any part of the universal sensor mounting stand.
- When using this stand, take care that excessive vibration is not applied to the sensor.