Discontinued Products
Specifications
| Model No. | SF-AC | |
|---|---|---|
| Connectable light curtains | PNP output type light curtains and Safety devices (SG-B1/A1/B2 series) manufactured by Panasonic Industry | |
| Applicable standards | EN 60947-5-1, EN ISO 13849-1(Category 4,PLe), EN ISO 13849-2, IEC 60947-5-1, ISO 13849-1(Category 4, PLe), ISO 13849-2, JIS B 9705-1(Category 4), ANSI/UL 508, CAN/CSA C22.2 No.14, OSHA1910.212, OSHA 1910.217(C), ANSI B11.1 to B11.19, ANSI/RIA 15.06 | |
| Control category | ISO 13849-1 compliance up to Category 4 | |
| Supply voltage | 24 V DC ± 10 % Ripple P-P 10 % or less | |
| Power consumption | 1.7 W approx. (at 24 V DC) (without any connected devices) | |
| Power supply for light curtain | 24 V DC ± 10 % | |
| Fuse (power supply) | Hybrid fuse, triggering current: 1.1 A or more, Reset after power down | |
| OSSD input | PNP transistor 2 inputs (S1, S2) | |
| Enabling path | NO contact × 3 (13-14, 23-24, 33-34) | |
| Utilization category | AC-15, DC-13 (EN 60947-5-1) | |
| Rated operational current(Ie)(Note 2) / Rated operational voltage | 6 A / 30 V DC, 6 A / 230 V AC, resistive load | |
| Contact material / contacts | AgSnO, Self cleaning, positively driven | |
| Contact resistance | 100 mΩ or less (initial value) | |
| Fuse | 6 A (slow blow) | |
| Mechanical lifetime | 10 million times (switching frequency 180 times/min.) | |
| Electrical lifetime | 100,000 times (switching frequency 20 times/min, rated load) | |
| B10d | At min.load:20,000,000 / At max.load :400,000 (ISO 13849-1) | |
| Pick-up delay | 40 ms or less (Automatic reset), 50 ms or less (Manual reset) | |
| Drop-out delay | 10 ms or less | |
| Auxiliary output | NC contact × 1 (41-42) | |
| Switching current | 1 A / 24 V DC | |
| Fuse | 1 A (slow blow) | |
| Alarm output (Note 3) | NC contact × 1 (51-52) (Non-safety contact, related to input “Alarm in”) | |
| Switching current | Max. 1 A / 24 V DC, Min. 5 mA / 24 V DC | |
| Fuse | 1 A (slow blow) | |
| Indicators | Power | Green LED (lights up when the power is supplied) |
| Internal circuit operation(Ui) | Green LED (lights up when both conditions are present: unit is powered up and hybrid fuse is at normal state) | |
| Relay operation (K1 / K2) | Green LED × 2 (lights up when enabling contacts are closed) | |
| Test input (Test) | Yellow LED (lights up when X11-X12 is opened) | |
| External relay monitor function | Incorporated | |
| Trailing edge function | Incorporated | |
| Test input polarity selection function | Incorporated (Selectable PNP or NPN test input polarity by internal switch) | |
| Excess voltage category | III | |
| Rated impulse-withstand voltage (Uimp) | 4 kV | |
| Pollution degree | 2 | |
| Environmental resistance | Degree of protection | Enclosure : IP40, Terminal : IP20 |
| Ambient temperature | -10 to +55 ℃ +14 to +131 ℉, Storage: -10 to +55 ℃ +14 to +131 ℉ | |
| Ambient humidity | 35 to 85 % RH, Storage: 35 to 85 % RH | |
| Vibration resistance | 10 to 55 Hz frequency, 0.35 mm 0.014 in amplitude in X, Y, Z directions for three times each (in power OFF state) | |
| Shock resistance | 15 G (150 m/s2 approx.) Effective impulse time 11ms | |
| Material | Enclosure: Polycarbonate | |
| Connection terminal | Removable European terminal | |
| Tightening torque | 0.6 N·m | |
| Wiring cable | 0.2 to 2.5 mm2 [including single wire or ferrule (sleeve)] | |
| Mounting | Complies with 35 mm width DIN rail (EN 50022) | |
| Weight | Net weight: 400 g approx. | |
Note 1 : Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 ℃ +68 ℉.
Note 2 : The rated operational current (le) varies depending on the ambient temperature. Refer to the below figure.
Note 3 : The alarm output is "open" when the alarm input from the light curtain is ON.
Dimensions
- Unit: mm in
Wiring
Please install and connect ferrule (stick) terminal when the lead wire of the connected equipment is a twisted wire.
Please do not connect the twisted wire directly with the terminal.
Tighten the wiring to the wiring terminal block at tightening torque of 0.6 N m.
Others
The seal as shown in the drawing on the right is stuck to the engagement point of unit. When the seal is peeled off or broken, this equipment will not be certified as ‘Safety equipment’.
Functional description
Derating
Rated operation current (le) of enabling path changes depending on ambient temperature.
