Panasonic Industry / Automation Controls
MENU
Panasonic Industry / Automation Controls

ST4-C11｜Compact Type 4 Safety Beam Sensor ST4

Download

*Photo may vary from actual product.

This product has been confirmed that it does not contain the 6 substances specified in EU RoHS Directive 2011/65/EU and the 4 substances specified in 2015/863/EU.

Product Number

ST4-C11

Part Number

ST4-C11

Product

Compact Type 4 Safety Beam Sensor

Details

Controller

Product Name

 Compact Type 4 Safety Beam Sensor ST4

Contact Us

*Specifications and design of the products are subject to change without notice for the product improvement.

Spec Detail

Specifications and design of the products are subject to change without notice for the product improvement.
ItemSpecifications
Part NumberST4-C11
Product NumberST4-C11
Products NameCompact Type 4 Safety Beam Sensor
Product detailsController
The price of the productPlease contact our office
Applicable standardsIEC 61496-1/2 (JIS B 9704-1/2 / UL 61496-1/2) (Type 4), ISO 13849-1:2015 (Category 4, PLe), JIS B 9705-1 (Category 4), IEC 61508-1 to 3 (SIL3), IEC 62061 (SIL3), JIS C 0508-1 to 3 (SIL3), UL 1998, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI/RIA R15.06, ANSI/ISA S84.01 (SIL3)
(Note) Complies with those standards only when the controller is used in combination with the sensor head ST4-x.
CE marking directive complianceMachinery Directive, EMC Directive, RoHS Directive
Power voltage24 V DC +10-15 % Ripple P-P 10 % or less
Current consumption100 mA or less (excluding sensor head ST4-Ax)
PFHDRefer to the following table(Note： (Probability of dangerous failure per hour) depends on number of single beam sensor ST4-A□ connected to controller.)
MTTFDMore than 100 years (Note：Mean time to dangerous failure (in years))
Environmental resistance:Degree of protectionEnclosure: IP40 (IEC)
Terminal: IP20 (IEC)
Environmental resistance:Ambient temperature－10 to +55 ℃ +14 to +131 ℉ (No dew condensation or icing allowed),
Storage: －25 to +70 ℃ －13 to +158 ℉
Environmental resistance:Ambient humidity30 to 85 % RH, Storage: 30 to 95 % RH
Environmental resistance:Voltage withstandability1,000 V AC for one min. between all supply terminals connected together and enclosure
Environmental resistance:Insulation resistance20 MOhm or more with 500 V DC mega between all supply terminals connected together and enclosure
Environmental resistance:Vibration resistance10 to 55 Hz frequency, 0.75 mm 0.030 in double amplitude or maximum acceleration 90 m/s2 in X, Y and Z directions for two hours each<
Environmental resistance:Shock resistance300 m/s2 acceleration in X, Y and Z directions three times each
MaterialEnclosure: ABS
Applicable sensor headST4-Ax
Applicable sensor head:No. of series connectionsInterference prevention possible when up to a maximum of 6 sets are connected(When the maximum of 3 controllers are connected together, interference prevention is possible for up to 18 sets)
Control outputs (OSSD 1, OSSD 2)PNP open-collector transistor / NPN open-collector transistor Dual output x 1 system (Set using output polarity selection switch)
[PNP output]
Maximum source current: 200 mA
Applied voltage: same as the supply voltage (between control output and +V)
Residual voltage: 2.5 V or less (at 200 mA source current)
Leakage current: 200 micro A or less (including power OFF condition)
Maximum load capacity: 1 micro F (from no-load to max. source current)
Load wiring resistance: 3 Ohm or less (between control output and load)
[NPN output]
Maximum sink current: 200 mA
Applied voltage: same as the supply voltage (between control output and 0 V)
Residual voltage: 2.0 V or less (at 200 mA sink current)
Leakage current: 200 micro A or less (including power OFF condition)
Maximum load capacity: 1 micro F (from no-load to max. sink current)
Load wiring resistance: 3 Ohm or less (between control output and load)
(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less.
Control outputs (OSSD 1, OSSD 2):Operation modeON when all beams of the connected ST4-Axs are received
OFF when one or more beams of the connected ST4-Axs are interrupted
OFF during lockout
Control outputs(OSSD1, OSSD2):Protection circuitIncorporated
Response timeOFF response: 25 ms or less
ON response: 90 ms or less (auto reset) / 140 ms or less (manual reset)
Auxiliary outputsPNP open-collector transistor / NPN open-collector transistor (Set using output polarity selection switch)
ST4-C11: one output
ST4-C12EX: four outputs
[PNP output]
Maximum source current: 100 mA
Applied voltage: same as the supply voltage (between auxiliary output and +V)
Residual voltage: 2.5 V or less (at 100 mA source current)
[NPN output]
Maximum sink current: 100 mA
Applied voltage: same as the supply voltage (between auxiliary output and 0 V)
Residual voltage: 2.0 V or less (at 100 mA sink current)
(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less.
Auxiliary outputs:Operation modeOFF when all beams of the connected ST4-Axs are received
ON when one or more beams of the connected ST4-Axs are interrupted
Auxiliary outputs:Protection circuitIncorporated
Muting lamp output-
(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less.
Muting lamp output:Protection circuitIncorporated
Connection terminalDetachable spring-cage terminal
Wiring cableTerminal block connector: 0.2 to 1.5 mm2
WeightNet weight: 180 g approx
Gross weight: 390 g approx

MENU

Recently checked products

Recently checked product numbers