Panasonic Industry / Automation Controls
MENU
Panasonic Industry / Automation Controls

FX-502P｜Digital Fiber Sensor FX-500 Ver.2

Download

*Photo may vary from actual product.

This product has been confirmed that it does not contain the 6 substances specified in EU RoHS Directive 2011/65/EU and the 4 substances specified in 2015/863/EU.

Product Number

FX-502P

Part Number

FX-502P

Product

Digital Fiber Sensor

Details

2-output type

Product Name

 Digital Fiber Sensor FX-500 Ver.2

Contact Us

*Specifications and design of the products are subject to change without notice for the product improvement.

Spec Detail

Specifications and design of the products are subject to change without notice for the product improvement.
ItemSpecifications
Part NumberFX-502P
Product NumberFX-502P
Products NameDigital Fiber Sensor
Product details2-output type
Applicable regulations and certificationsCE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations), UL/c-UL Listing certification
Supply voltage12 to 24 V DC+10-15 % Ripple P-P 10 % or less
Power consumptionNormal operation: 960 mW or less (current consumption 40 mA or less at 24 V supply voltage)
ECO mode: 680 mW or less (current consumption 28 mA or less at 24 V supply voltage)
Output 1, Output 2PNP open-collector transistor
- Maximum source current: 50 mA (Note 1)
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 2 V or less (Note 2) (at maximum source current)
(Note 1) 25 mA max. if 5 or more standard types are connected together.
(Note 2) 50 mA max. if 5 or more standard types are connected together. (25 mA in case of 2-output type and cable type)
Output 1, Output 2:Output points2 points
Output 1, Output 2:Output operationSwitchable either Light-ON or Dark-ON by L/D mode
Output 1, Output 2:Short-circuit protectionIncorporated
Response timeH-SP: 25 micro s or less
FAST: 60 micro s or less
STD: 250 micro s or less
LONG: 2 ms or less
U-LG: 4 ms or less
HYPR: 24 ms or less, selectable
External input-
External input(switchable with Output 2)PNP non-contact input
- Signal condition
High: +4 V to +V DC (at 3 mA sink current)
Low: 0 to +0.6 V DC or Open
- Input impedance: 10 kOhm approx.
Possible external input functionEmission halt / Teaching (Full-auto, Limit, 2-point) / Logic operation setting / Copy lock / Display adjustment / Data bank load / Data bank save, selectable
Sensitivity setting2-point teaching / Limit teaching / Full-auto teaching / Manual adjustment
Incident light intensity display rangeH-SP / FAST / STD: 0 to 4,000
LONG: 0 to 8,000
U-LG / HYPR: 0 to 9,999
Timer functionIncorporated with variable OFF-delay / ON-delay /One-shot / ON-delay - OFF-delay / ON-delay - One-shot timer, switchable either effective or ineffective
Incorporated with variable OFF-delay / ON-delay /One-shot timer, switchable either effective or ineffective
Timer function:Timer periodTimer range ''ms'': 0.5 ms approx., 1 to 9,999 ms approx., 1 ms approx.
Timer range ''sec.'': 0.5 s approx., 1 to 32 s approx., 1 s approx.
Timer range ''1/10 ms'': 0.05 ms approx., 0.1 to 999.9 ms approx., 0.1 ms approx.
each output is set individually
Emission amount setting functionIncorporated, 3 levels (each level 25 to 100 %) + Auto setting [1 level (25 to 100 %) when using H-SP mode]
Interference prevention functionIncorporated (Note) , selectable either automatic interference prevention or different frequency
(Note) Number of sensor heads which is possible to be mounted closely in auto interference prevention function depends on response time as shown in table below.Number of sensor heads which is possible to be mounted closely in different frequency Interference prevention function is up to 3 units.
- Number of sensor heads mountable closely (Unit: set)
Response time: IP-1
H-SP: 0
FAST: 2
STD: 4
LONG: 8
U-LG: 8
HYPR: 12
Various settingsHysteresis setting / Shift amount setting / Emission power setting / Display turning setting / ECO setting / Data bank loading saving setting / Copying setting / Code setting / Reset setting / Logical calculation setting / Threshold value tracking setting, etc.
ProtectionIP40 (IEC)
Ambient temperature-10 to +55 ℉ +14 to +131 ℉ [If 4 to 7 units are mounted in cascade: -10 to +50 ℉ +14 to +122 ℉　or if 8 to 16 units are mounted in cascade: -10 to +45 ℉ +14 to +113 ℉　] (No dew condensation or icing allowed), Storage: -20 to +70 ℉ -4 to +158 ℉　
Vibration resistance10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude (10 G max.) in X, Y and Z directions for two hours each
Shock resistance98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Emitting element (modulated)Red LED (Peak emission wavelength: 643 nm 0.025 mil)
MaterialEnclosure, Case cover: Polycarbonate
Switch: Polyacetal
Cable-
Cable extension-
WeightNet weight: 15 g approx.
Gross weight: 70 g approx.
AccessoryFX-MB1 (Amplifier protection seal): 1 set

MENU

Recently checked products

Recently checked product numbers