Panasonic Industry / Automation Controls
MENU
Panasonic Industry / Automation Controls

FX-101P-CC2｜Digital Fiber Sensor FX-100

Download

*Photo may vary from actual product.

This product has been confirmed that it does not contain the 6 substances specified in EU RoHS Directive 2011/65/EU and the 4 substances specified in 2015/863/EU.

Product Number

FX-101P-CC2

Part Number

FX-101P-CC2

Product

Digital Fiber Sensor

Details

Standard type [Cable set]

Product Name

 Digital Fiber Sensor FX-100

Contact Us

*Specifications and design of the products are subject to change without notice for the product improvement.

Spec Detail

Specifications and design of the products are subject to change without notice for the product improvement.
ItemSpecifications
Part NumberFX-101P-CC2
Product NumberFX-101P-CC2
Products NameDigital Fiber Sensor
Product detailsStandard type [Cable set]
The price of the productPlease contact our office
Applicable regulations and certificationsCE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations), UL/c-UL Listing certification
Supply voltage12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
Power consumptionNormal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
OutputPNP open-collector transistor
- Maximum source current: 100 mA
- Applied voltage: 30 V DC or less (between output and +V)
- Residual voltage: 1.5 V or less (at 100 mA source current)
Output:Output operationSelectable either Light-ON or Dark-ON, at SET mode
Output:Short-circuit protectionIncorporated
External inputPNP non-contact input
- Signal condition
High: +4 V to +V DC (Sink current 0.5 to 3 mA)
Low: 0 to +0.6 V DC or Open
- Input impedance: 10 kOhm approx.
Response timeEmission frequency 0: 250 micro s or less (factory default setting)
Emission frequency 1: 450 micro s or less
Emission frequency 2: 500 micro s or less
Emission frequency 3: 600 micro s or less
Sensitivity setting2-point teaching / Limit teaching / Full-auto teaching
Operation indicatorOrange LED (lights up when the output is ON)
Digital display4 digits (green) + 4 digits (red) LCD display
Fine sensitivity adjustment functionIncorporated
Timer functionON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
Emission amount setting function3-level + Auto setting (from production in December 2007)
Interference prevention functionIncorporated Emission frequency selection method (Functions at emission frequency 1, 2 or 3)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
However, the interference prevention function does not operate at emission frequency 0 (factory default setting).
Ambient temperature–10 to +55 ℃ +14 to +131 ℉
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 ℉, if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ℉) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158 ℉
Ambient humidity35 to 85 % RH, Storage: 35 to 85 % RH
Ambient illuminanceIncandescent light: 3,000 lx or less at the light-receiving face
Voltage withstandability1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
Insulation resistance20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
Vibration resistance10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
Shock resistance98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
Emitting element (modulated)Red LED (Peak emission wavelength: 643 nm 0.025 mil)
MaterialEnclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
Connection methodConnector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Cable lengthTotal length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
WeightNet weight: 15 g approx.
Gross weight: 75 g approx.
AccessoryFC-FX-1(Protection cover): 1 pc. (Note)
CN-14A-C2 (Connector attached cable, 2 m 6.562 ft long): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.

MENU

Recently checked products

Recently checked product numbers