{lead}
{name}
  • {name}
  • 日本語
  • English (Global)
  • English (Asia Pacific)
  • 简体中文
  • 繁體中文
  • 한국어
▼
Panasonic Industry / Automation Controls
MENU
Panasonic Industry / Automation Controls

HG-S1110-AC｜Contact-Type Digital Displacement Sensor HG-S

Download

*Photo may vary from actual product.

This product has been confirmed that it does not contain the 6 substances specified in EU RoHS Directive 2011/65/EU and the 4 substances specified in 2015/863/EU.

Product Number

HG-S1110-AC

Part Number

HG-S1110-AC

Product

Contact-Type Digital Displacement Sensor

Details

Air-driven type
10 mm 0.394 in type High precision

Product Name

 Contact-Type Digital Displacement Sensor HG-S

Contact Us

*Specifications and design of the products are subject to change without notice for the product improvement.

Spec Detail

Specifications and design of the products are subject to change without notice for the product improvement.
ItemSpecifications
Part NumberHG-S1110-AC
Product NumberHG-S1110-AC
Products NameContact-Type Digital Displacement Sensor
Product detailsAir-driven type
10 mm 0.394 in type High precision
Applicable regulationsCE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations)
Applicable controllerHG-SC101(-P), HG-SC111(-P), HG-SC112(-P), HG-SC113
(Note) : Be sure to use the sensor in combination with an HG-SC□ controller manufactured in or after February 2019.
Position detection methodOptical absolute linear encoder method
Measurement range10 mm 0.394 in
(Note) : The position that represents "0" as an absolute value is a position where the spindle is pushed further down from the bottom dead point by 0.1 mm 0.004 in or more. The term "stroke" indicates the total stroke length from the bottom dead point to the top dead point.
Stroke10.5 mm 0.413 in or more
(Note) : The position that represents "0" as an absolute value is a position where the spindle is pushed further down from the bottom dead point by 0.1 mm 0.004 in or more. The term "stroke" indicates the total stroke length from the bottom dead point to the top dead point.
Measuring force・Measuring force changes with the air pressure used. Removing the seal cap enables the product to be used as the low measuring force type.
・Refer to the product page or catalog for the relationship between supplid air pressure, spindle position and the measuring force.
Resolution0.1 μm 0.004 mil
Sampling rate1 ms
Indication accuracy(P-P)Full range: 1.0 μm 0.039 mil or less
Limited range: 0.5 μm 0.02 mil or less
(any 60 μm 2.362 mil)
Tip deviation amount35 μm 1.378 mil (typical value)
Hot swap functionIncorporated
Working pressure range0.14 to 0.16 MPa
With no seal cap mounted : 0.035 to 0.045 MPa
Capacity to resist pressure0.2 MPa
Usable fluidClean air (Dew point temperature: -10 ℃ +14 ℉ or less)
Applicable tubeOutside diameter: ø4 mm ø0.157 in / Inside diameter: ø2.5 mm ø0.098 in
Operation indicatorEquipped (2-color LED: Orange / Green)
Pollution degree2
Operating altitude2,000 m 6561.68 ft or less
(Note) : Do not use or store in an environment that has been pressurized to an air pressure higher than the atmospheric pressure at 0 m.
Environmental resistance : ProtectionIP67 (IEC)
With no seal cap mounted : -
(Note) : Protective structure is not applicable when the sealing portions have deteriorated or become damaged. The protection level is zero when the seal cap is removed.
Environmental resistance : Ambient temperature-10 to +55 ℃ +14 to +131 ℉ (No dew condensation or icing allowed),
Storage: -20 to +60 ℃ -4 to +140 ℉
Environmental resistance : Ambient humidity35 to 85 % RH, Storage: 35 to 85 % RH
Insulation resistance100 MΩ or more at 250 V DC
Environmental resistance : Vibration resistance10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (10 to 58 Hz), maximum acceleration 196 m/s2, (58 to 150 Hz) in X, Y, and Z directions for two hours each
Environmental resistance : Shock resistance1,960 m/s2 acceleration in X, Y, and Z directions three times each
Grounding methodCapacitor grounding
MaterialBody: Zinc, Holder: Stainless steel, Spindle: Tool steel, Probe (Note): Brass (body) / Ceramic (ball),, Air tube clamp: S60CM
(Note) : The probe is also available as an option.
WeightNet weight: 80 g approx.
AccessorySensor head fastening wrench: 1 pc., Mounting nut: 1 pc., Seal cap: 1pc, Air tube clamp: 1 pc.
RemarkWhere measurement conditions are not specified, the conditions used were as follows: standard type measurement probe (HG-SS10C), ambient temperature of +20 ℃ +68 ℉, and a clean atmosphere where water, oil, other liquids or dust does not come in contact with the equipment.

MENU

Recently checked products

Recently checked product numbers