Laser Marker Smart Utility Detailed Version-Up Information
Version-up Information
Version-Up Information (Ver.3.5.0 to Ver.3.5.1) (September 17, 2024 update)
The following points have been upgraded.
The input range for the trigger detection position setting has been changed to allow for negative values (downstream side) in addition to positive values (upstream side).
Version-Up Information (Ver.3.4.2 to Ver.3.5.0) (August 28, 2024 update)
The following points have been upgraded.
Pre-scan optimization level setting ( 3 levels to control presence of pre-scan depending on angle ) has been added for pre-scan function.
Changed the command history's initial scrolled state to be at the lastest history position.
Added an additional control method (activate until fixed time) for time hold function.
LmUtil Operation Manual is included with installation of Laser Marker Smart Utilty.
Setting to enable or disable checking whether a figure in a DXF file is closed or not is added in response to problem of missing hatching lines when all the sides of the figure are not connected( not closed ).
Added a function to search for laser markers by directly specifying the IP address.
Changed the exit code from [999] to [304] when the file added by the Execute option of LmUtil exceeds the upper limit in the laser marker.
Changed the exit code from OK to [406] when the file added by the PutMarkingFile option of LmUtil exceeds the upper limit in the laser marker.
Fixed an issue where pressing the Tab key does not move to the next input field when entering QR code and data matrix settings.
Added the ability to input and output marking files in XML format using LmUtil.
Fixed an issue where hatch lines could extend outside the shape in certain DXF files.
Fixed an issue where the laser marker name could not be read when the Target command was executed in LmUtil.
Fixed an issue where an error E690 did not occur when marking data was placed outside the range of the 3D model of the cone(horizontal).
The following Chinese translations of logo data editing software have been changed. 「终点调适」⇒「端点调适」
Added a setting item that allows you to set the character width to the same as that of LP-400/V/M/S/Z for "Character spacing type: Justify" in the character object settings.
Improved error messages for combinations of Defocus and Spot Uniform modes. "Some setting fields contain an improper value." ⇒ "When uniform spot mode is activated, set the defocusing value to ≤0."
Fixed an issue where changing the line width would distort logo data using the DXF file shape (circle/arc) .
Fixed an issue where when installing Laser Marker Smart Utility by selecting a language different from the OS language of the PC, the logo data editing software was partially garbled.
When the object group is set to Marking OFF, "Marking ON/OFF" and "Guide laser display" of the marking object are hidden.
Fixed a problem where the time was not fixed in the marking image display of the monitor panel while using the timehold function. (No effect on marking)
Fixed an issue where closing the Laser Marker NAVI smart window during the lot setting operation, an unintended communication error was displayed.
Corrected the name of the setting item of GS1 DataBar Expanded Stacked. "Symbol characters in a row" ⇒ "Segments per row"
Fixed an issue where Laser Marker NAVI smart could not be started when the PC was disconnected from the network after offline editing of a marking file placed in a network folder.
Version-Up Information (Ver.3.4.1 to Ver.3.4.2) (May 7, 2024 update)
The following points have been upgraded.
To improve compatibility with LP-400/V/M/S/Z, selectable option is added for not generating a warning even when the graphic file is not specified.
Improvement made to show barcode and 2D code sizes that does not include quiet zone.
Version-Up Information (Ver.3.3.0 to Ver.3.4.1) (April 1, 2024 update)
The following points have been upgraded.
Fixed an issue where the system offset setting is reflected in the marking image.
When the version of the LP-AEB10 expansion board and the laser marker do not match at the first startup, the language can be set.
When the Z position of the LP-ZV is set, when the sum of the Z position and defocus setting exceeds the range of -25mm~+25mm, the E692 error is correctly generated.
When the defocus setting value is greater than 0 when the spot uniform mode is enabled on the LP-ZV, a warning that the setting range has been exceeded is displayed on the NAVI Smart screen.
Fixed an issue where when converting a file using the 3D settings of the LP-M/Z series, if the rotation of the entire file condition is set, it will be displayed and printed in a different position than before conversion.
Fixed an issue when in 3D cone setting, the focal position is affected by the direction of the marking line.
Fixed an issue where file conversion could not be performed in an Japanese environment when the file name or folder name of an LP-400/V/M/S/Z file contains characters other than Japanese.
Fixed an issue where the position of visible characters in barcodes and 2D codes could not be set when NAVIsmart 2.0.0 or later and LP-GS/RC/RF/RV with controller version lower than 2.0.0 were connected online.
Fixed an issue where E661 may occur when the marking data is outside the area range in 3D setting printing instead of E692.
Fixed an issue where some CODE128 visible characters were not displayed when connecting NAVIsmart 3.2.0 or later and LP-RF/RV/ZV with controller version less than 3.2.0 online, or editing LP-RF/RV marking files.